Probes Manager

<< Click to Display Table of Contents >>

Navigation:  EDGE > Devices > Data Loggers >

Probes Manager

The Probes Manager logger interface in EDGE provides the versatility of selecting from a variety of models of the same logger, at the same time allowing for differentiating between data import loggers and live loggers.  


The Probes Manager is launched each time a logger is selected from the Devices ribbon.      




Assuming the In-Situ logger is selected, the Probe Manager presents a selection of all In-Situ sensor models supported by EDGE.        


Select Sensor


The Select Sensor option appears. In the example below, the selected In-Situ_Level500 provides the option of opening the data file associated with this logger. Information about where the example data files are located is visible in the Select Sensor window (as a general rule, for demonstration purposes, data files are available in EDGE in the EDGE\Tutor\SensorExamples folder).  


25321_Sensor_2018-09-07_1255_probes manager_2_in-situ


If a live sensor is chosen, such as Modbus in the example below, an additional option is presented to the user, allowing for connection to the live sensor and importing data in a real-time manner. The data can be imported in any of the tabs that support data import, as these are selected by the user. In this example, four tabs are available and all four were selected to import data from the live sensor.


25321-ModBus-2018-09-07_1258_probes manager_3_in-situ_modbus


Once the Connect button is selected, a sensor interface will display, where manipulation of data import, probe and sensor details, and remapping options are available.  


Imported Data Tab


The Imported Data tab displays all data available from the live importing from the sensor.


25321-Modbuscolumns2018-09-07_1330probes manager_4_in-situ_modbus_data


Probe Tab


The Probe tab provides information about the probe, including the probe vendor, probe model, and probe port.


25321-ProbeTab-2018-09-07_1340 probes manager_5_in-situ_modbus_probe


Filtering Tab


The Filtering tab allows for selection of data being imported, including:

Time Limitation – Allows trimming of imported data records (as captured on the Imported Data tab) by assigning a Start Time and End Time. An option is also available to disconnect the probe automatically after the End Time is reached.  

Record Limitation – Allows the user to select how many records will be added.




Two options are available at the bottom right of the Filtering tab:

Apply Filters – Enables application of all settings selected in Time Limitation and Record Limitation.

Clear All Filters – Allows for clearing of all settings selected in Time Limitation and Record Limitation.


Columns & Remaps Tab


The Columns & Remaps tab displays all parameters being imported.




The following columns are available on the tab:


IsVisible – Allows selection of the parameters visible for data import. Only the parameters checked as IsVisible in this tab will show in the Imported Data tab.




CurrentName and CurrentUnit – Displays the name and corresponding units of the imported parameters.


ExternalName and ExternalUnit – Parameters as imported from the sensor.


InternalName and InternalUnit – Parameters as imported in EDGE.


DecimalNum – Allows trimming the number of decimals recorded in EDGE from selected parameters. The maximum number of decimals is set to 10. Any number exceeding 10 will default to 10.


Remapped – Allows selection of parameters to be remapped after import. Parameters are automatically remapped if possible. The Remapped column for that field will be checked if the Internal value in the RT_REMAP_DETAILS table has been set for this field.


Three other options are available on the bottom right of the Columns & Remaps tab:

Mark All Invisible – Allows users to to mark all rows as invisible.

Mark All Visible – Allows users to mark all rows as visible.

Remap All – Selects all parameters to be remapped.


Individual selection/deselection of each row in these column is available by clicking in the specific check box.


Parameters Tab


The Parameters tab displays the imported parameters as Selected or Last Received. The Selected option displays the last row of selected data to be imported. The Last Received Data (Live) option displays the last row of received data.


25321-Parameters-2018-09-07_1439 probes manager_8_in-situ_modbus_parameters


Sensors Tab


The Sensors tab provides detailed information about each of the sensors used to gather the data.


25321-Sensors-2018-09-07_1443 probes manager_9_in-situ_modbus_sensors